Unable to start First of all, check the power supply situation: whether the connection is solid or not; whether the switch is in close contact; whether the fuse is blown; whether the three-phase power supply is equal or not. If there is an open circuit, poor contact, the fuse blown, lack of phase, should identify the cause and timely repair. Second, check if it is a mechanical failure of the pump itself, common causes are: packing is too tight or clogged with debris between the impeller and the pump body; pump shaft, bearings , leak ring rust live; serious shaft and other bending. Remedy: relax the filler, clear the diversion trough; open the pump body to remove debris, rust ; remove the pump shaft to correct or replace the new pump shaft. Matching power motor overheating There are four reasons. First, the reasons for the power: high or low voltage, under a specific load, if the voltage range should be rated at + 10% to -5% outside the motor will cause overheating; power supply three-phase voltage asymmetry, power supply three phase voltage imbalance phase exceeds 5%, will lead the winding overheating; missing running, experience table Ming agricultural motor burned more than 85% due to the operation of phase caused by phase cope motor mounting protection device. Second, the reasons for the pump: the choice of power does not support the cart pull the motor, the motor overloaded for a long time to run, so that the motor temperature is too high; start too often, the fixed short-term or intermittent work of the motor system for continuous work. Should limit the number of starts, the correct choice of thermal protection, according to the rated motor on the use of fixed. Third, the reasons for the motor itself: the wrong connection, the △ wrongly connected into a Y-shaped, so that the motor temperature rose rapidly; stator windings have short-circuit between, turn short circuit or local grounding, light motor overheating, severe insulation Burn out; Broken squirrel cage rotor or defective, the motor running 1 to 2 hours, the core temperature rises rapidly; ventilation system failure, the fan should be checked for damage, rotation direction is correct, the ventilation hole is blocked; bearing wear, the rotor Eccentric sweep bore to make the rotor core rubbed metal percussion sound, the core temperature rose rapidly, the motor smoke in serious cases, and even the coil burned. Fourth, the reasons for the work environment: Motor winding damp or dust, oil and other attached to the winding, resulting in reduced insulation. Insulation resistance of the motor should be measured and cleaned, dried; Ambient temperature is too high. When the ambient temperature exceeds 35 ℃, the inlet air temperature is high, the motor temperature will be too high, should seek to improve its working environment. Such as scaffolding shade and so on. Reminded: due to electrical reasons for failure, should obtain professional qualifications electrician maintenance, knowledgeable people can not be blindly repaired to prevent personal injury accidents. Pump heat Reason: bearing damage; rolling bearing or bracket cover clearance is too small; shaft bending or two axes are not the same; tape is too tight; lack of oil or poor oil quality; impeller balance hole blocked, impeller out of balance, increasing the direction Thrust on one side. Remedy: Replace the bearing; Remove the back cover, install the gasket between the bracket and the bearing seat; Investigate the pump shaft or adjust the concentricity of the two shafts; Adjust the tightness of the tape properly; Fill the clean butter and butter About 60% of the gap; clear the balance hole plug. Insufficient traffic This is because: the power or speed of the belt slip is not complete, so that the rotational speed is low; axial flow pump blade mounting angle is too small; insufficient head, conduit or pipe with a long right turn; high suction; bottom valve , conduit And impeller partial blockage or impeller defect; outlet pipe serious water leakage. Remedy: Restore the rated speed, remove the belt grease, adjust the belt tightness; adjust the blade angle, reduce the pump installation position, shorten the pipe or change the pipe curvature; seal the pump leak, compaction packing; clear blockage Change the impeller; replace the leak ring, plug the leak. Absorption of water The reason is that there is air in the pump body or inlet gas, or at the end of the valve is not strict Irrigation irrigation dissatisfaction, vacuum pump packing serious leaks, gate valve or rattan closed lax. Remedy: First water pressure up, and then filled with water pump, and then boot. At the same time check the check valve is tight, piping, fittings leaks, such as found leakage, remove the joint at the joints coated with oil or paint, and tighten the screws. Check the pump shaft seal ring, such as serious wear and tear should be replaced with new pieces. Piping leaks or leaks. Nuts may not be tightened during installation. If the leakage is not serious, can be smeared in the place of leakage or leakage of cement , or coated with asphalt mixture of cement slurry. Temporary repair can be painted wet mud or soft soap. If the joint leaks, you can use a wrench to tighten the nut, if serious leakage must be re-disassembly, replacement of cracked pipe; reduce the head, the pump nozzle into the water 0.5m. Severe vibration Mainly for the following reasons: Electric rotor imbalance; Coupling bad; Bearing wear and tear; Rotating parts of the loose, broken; Pipe stent is not strong and other reasons. Can be taken to adjust, repair, reinforcement, straightening, replacement and other methods.
The new toy trends this year are all about getting your kids active, getting their brains engaged, and thankfully, cutting down their screen.There's nothing complicated about play. The only energy needed is your child`s and there`s plenty of that. Our safe and fun children's toys motivate kids to develop fine motor skills, social skills and logical thinking through role play, imagination, creativity and movement.
VALUABLE TEXTILE CO., LTD is a comprehensive modern enterprise integrating manufacturing and sales. Since its establishment in 2016, the company has risen rapidly in the Home Textile industry with its professional technical ability and mature craft production level. Valuable Textile Co., Ltd. is a manufacturer which focus on producing different kinds of indoor and outdoor mosquito nets,bed canopy, baby canopies, kid play tents. Every year, VALUABLE exported to over 20 countries and up to 2,000,000 pieces of products to the whole world.
Kids Toy,Cloth Book,Kids Play Tent,Kids Blanket,Kids Toy Product Valuable Textile Co., Ltd. , https://www.valuablecanopies.com
Common faults of agricultural small water pump and its maintenance and adjustment methods
Agricultural small water pump is living water and spring in the Rural Summer of major irrigation machinery. In operation, it is inevitable failure and damage, so that normal pumping can not. Therefore, poor pumping of the pump must be repaired and adjusted to promptly troubleshoot.